Beaumont Concrete Calculator







Beaumont Concrete Calculator | Cubic Yards, Bags & TX Cost | Free Tool



🤠 TDLR LICENSED · IBC COMPLIANT · GOLDEN TRIANGLE TX
✓ 100% Free

Beaumont
Concrete Calculator — Yards, Bags & Cost

Calculate cubic yards, bags needed, and Beaumont-accurate ready-mix costs for any SE Texas concrete project — driveways, patios, slab foundations, footings & more.

$155
Avg Beaumont Ready-Mix (per Cu Yd)
3,500
Min PSI — Beaumont Residential
95°F
Peak Summer Temp — Beaumont TX
TDLR
TX Dept of Licensing & Regulation
🚗 Driveway
🏠 Slab Foundation
🛤️ Patio / Slab
🏗️ Foundation
🪨 Footings
🏢 Commercial Slab


The Beaumont Concrete Calculator helps homeowners, contractors, and builders estimate cubic yards, bag count, and ready-mix costs for any concrete project in Beaumont, TX. Beaumont pricing typically runs $140–$195/yd, driven by the active Southeast Texas construction and petrochemical industry market. Beaumont’s biggest concrete challenge is its notorious expansive Beaumont Clay soil — which can shift slabs by inches if sub-base preparation is skipped — combined with a hot, humid climate that narrows finishing windows in summer months. Enter your dimensions for instant, Beaumont-accurate results. Explore more free tools at Concrete Toolkit.

🤠 Beaumont Concrete Calculator

🤠 Beaumont-Accurate Pricing · TDLR Compliant · SE Texas
Beaumont Concrete Calculator
Cubic yards, bags needed & Beaumont TX ready-mix cost — instant results
🚗 Driveway
🏠 Slab Foundation
🛤️ Patio
🏗️ Foundation
🪨 Footings

Enter your project dimensions to calculate volume, bags needed, and estimated Beaumont TX material cost.


Residential driveway: 4–5 in. min, 3,500 PSI. Fiber mesh recommended for Beaumont clay. City of Beaumont permit required.








Sidewalk 4 in · Driveway 4–5 in · Patio 4 in · Foundation 4–5 in · Footing 8–12 in




Cubic Yards Required
—
Including waste factor

📋 Project Summary

    💵 Beaumont Cost Estimate

      📐 Beaumont Driveway Cross-Section — SE Texas Standard Layers

      Broom / Exposed Aggregate Finish — Beaumont TX Standard
      Concrete — 4–5 in. (Beaumont Driveway)
      3,500 PSI · Fiber Mesh or #3 Rebar · Vapor Barrier Recommended
      ⬛ Fiber Mesh / #3 Rebar (Essential — Beaumont Expansive Clay Soil)
      🪨 4 in. Compacted Crushed Stone Base (TxDOT Spec)
      Compacted Subgrade / Beaumont Expansive Clay Soil
      27
      Cu ft per cubic yard
      45
      80 lb bags per cu yd
      $155
      Avg Beaumont ready-mix / yd
      Concrete Slab
      Fiber Mesh / Rebar
      Crushed Stone Base
      Clay Subgrade

      Beaumont Concrete Calculator — What You Need to Know

      Beaumont concrete work is shaped by two dominant challenges: the infamous Beaumont Clay — one of the most expansive soil types in the United States — which causes slab heave, driveway cracking, and foundation movement without proper base preparation; and a hot, humid subtropical climate where summer heat and 80%+ relative humidity create unpredictable finishing windows. The Texas Department of Licensing and Regulation (TDLR) licenses all general contractors performing concrete work in Texas — verify your contractor at tdlr.texas.gov. The City of Beaumont Building Services division issues permits for most flatwork, foundations, and structural concrete projects.

      🔵 Beaumont Minimum Concrete Requirements

      Residential driveways & patios: 3,500 PSI min, 4–5 in., fiber mesh or #3 rebar at 18-in. o.c. for clay soil · Slab foundations: 3,500–4,500 PSI post-tension design, 4–5 in., vapor barrier required · Structural / footings: 4,000–4,500 PSI, engineer-stamped plans required in Jefferson County · W/C ratio: max 0.50 for exposed slabs · Frost depth: 0–6 in. (no freeze-thaw concern in Beaumont). Always confirm with City of Beaumont Building Services before starting.

      🏠 Beaumont Slab Foundations

      Post-tension monolithic slabs are the standard for Beaumont residential construction due to the highly expansive clay. A typical 1,500 sq ft home slab at 4 inches needs ~7.5 cubic yards of 3,500–4,000 PSI concrete. Post-tension cable systems add $1,500–$3,000 to material cost but significantly reduce clay-related movement and long-term cracking.

      🚗 Beaumont Driveway Concrete

      Standard Beaumont driveways use 4–5 in. at 3,500 PSI with fiber mesh reinforcement. A typical 20×40 ft two-car driveway needs ~10 cubic yards. Beaumont’s high humidity means the finishing window can be deceptive — always have experienced finishers on site before the truck arrives, and avoid pours during or immediately after heavy rain events.

      🌧️ Beaumont Flood & Drainage

      Beaumont sits in a low-lying, flood-prone area with numerous FEMA flood zones. Concrete flatwork must slope away from all structures at a minimum 2% grade. Driveways and patios often require French drain integration or permeable paving provisions. Check your flood zone designation at FEMA Flood Map Service before finalizing slab elevation.

      How to Calculate Concrete Volume in Beaumont

      Measure length and width in feet and depth in inches. Multiply length × width × (depth ÷ 12) for cubic feet, then divide by 27 for cubic yards. For irregular patio shapes, divide into rectangles, calculate each, and add together. Always add 10% waste — Beaumont clay sub-base irregularities can create unexpected depth variations, and short-load fees of $100–$200 apply for orders under 3–5 cubic yards. For summer pours, schedule delivery before 9 AM and have your full crew ready before the mixer truck arrives.

      📐 Beaumont Concrete Formula

      Volume (cu ft) = Length (ft) × Width (ft) × [Depth (in) ÷ 12]
      Volume (cu yd) = Volume (cu ft) ÷ 27
      Order Qty = CEIL[ Volume (cu yd) × Waste Factor ]
      Example: 20 ft × 40 ft Beaumont driveway × 4 in = 266.7 cu ft = 9.88 cu yd → Order 11 cu yd

      ⚠️ Beaumont Humidity & Heat — Finishing Window Alert

      Beaumont’s summer humidity regularly exceeds 80–90% from June through September. In high-humidity conditions, the concrete surface can appear to set slowly while the interior hydrates quickly — creating a deceptive and narrow finishing window. Never over-trowel in humid conditions as it seals bleed water into the surface, causing delamination and scaling. Schedule summer pours before 9 AM, have all finishers on site before the truck arrives, and wet-cure with burlap and water immediately after final finishing for a minimum of 7 days.

      Beaumont Concrete Pricing — Current Reference

      Beaumont ready-mix pricing is close to the national average, supported by competitive supplier density in the Golden Triangle (Beaumont–Port Arthur–Orange) industrial corridor. Pricing rises 15–25% in rural East Texas (Jasper, Newton County) due to longer delivery distances and lower order volumes. Post-tension and fiber-reinforced mixes carry a modest premium but are widely recommended by Beaumont-area structural engineers for all clay-soil projects.

      Mix Type / PSI Beaumont Price / Cu Yd National Avg Best For Fiber Mesh? TX Use
      3,000 PSI — Standard $140–$165 $143–$158 Interior slabs, light patios Optional Light Use
      3,500 PSI — Residential $148–$178 $153–$166 Driveways, patios, slabs (standard BMT) Recommended Standard BMT
      4,000 PSI — TX Standard $158–$192 $161–$173 Foundations, exposed flatwork Recommended Compliant
      4,500 PSI — Structural $170–$208 $171–$181 Post-tension slabs, structural foundations Required Compliant
      5,000 PSI — High Strength $185–$225 $178–$193 Commercial, industrial, heavy load Required Compliant
      Colored / Stamped / Decorative $200–$255 $160–$200 Patios, pool decks, decorative drives Optional Popular BMT

      3,000 PSI — Standard

      Beaumont Price / Cu Yd$140–$165
      National Avg$143–$158
      Best ForInterior slabs, light patios
      TX UseLight Use

      3,500 PSI — Residential

      Beaumont Price / Cu Yd$148–$178
      National Avg$153–$166
      Best ForDriveways, patios, slabs
      TX UseStandard BMT

      4,000 PSI — TX Standard

      Beaumont Price / Cu Yd$158–$192
      National Avg$161–$173
      Best ForFoundations, exposed flatwork
      TX UseCompliant

      4,500 PSI — Structural

      Beaumont Price / Cu Yd$170–$208
      National Avg$171–$181
      Best ForPost-tension slabs, structural
      TX UseCompliant

      5,000 PSI — High Strength

      Beaumont Price / Cu Yd$185–$225
      National Avg$178–$193
      Best ForCommercial, industrial
      TX UseCompliant

      Beaumont & SE Texas Concrete Cost by Area

      Concrete pricing across the Golden Triangle and surrounding SE Texas region is relatively consistent, with Beaumont and Port Arthur sharing the most competitive rates due to higher construction volume and batching plant concentration. Rural Hardin, Jasper, and Newton counties carry delivery surcharges that can add $20–$45 per cubic yard to base mix pricing. Always confirm pricing and delivery range with your local supplier before ordering.

      SE Texas Area Key Cities 3,500 PSI / Cu Yd 4,000 PSI / Cu Yd Frost Depth Clay Risk
      Beaumont City Beaumont, South Park, Vidor $145–$175 $158–$190 0–6 in. High — Beaumont Clay
      Port Arthur Area Port Arthur, Groves, Port Neches $148–$178 $160–$195 0–6 in. High
      Orange / Bridge City Orange, Bridge City, Pinehurst $150–$182 $162–$198 0–6 in. Moderate–High
      Lumberton / Hardin Co. Lumberton, Silsbee, Kountze $155–$188 $165–$202 0–8 in. Moderate
      Rural SE Texas Jasper, Newton Co., Woodville $170–$215 $185–$228 0–8 in. Varies

      Beaumont City — Jefferson County

      3,500 PSI$145–$175/yd
      4,000 PSI$158–$190/yd
      Frost Depth0–6 in.
      Clay RiskHigh — Beaumont Clay

      Port Arthur Area

      3,500 PSI$148–$178/yd
      4,000 PSI$160–$195/yd
      Frost Depth0–6 in.
      Clay RiskHigh

      Orange / Bridge City

      3,500 PSI$150–$182/yd
      4,000 PSI$162–$198/yd
      Frost Depth0–6 in.
      Clay RiskModerate–High

      Lumberton / Hardin County

      3,500 PSI$155–$188/yd
      4,000 PSI$165–$202/yd
      Frost Depth0–8 in.
      Clay RiskModerate

      Rural SE Texas

      3,500 PSI$170–$215/yd
      4,000 PSI$185–$228/yd
      Frost Depth0–8 in.
      Clay RiskVaries

      ✅ Beaumont Concrete Pro Tip — Beaumont Clay Prep

      The single most common cause of failed Beaumont concrete projects is skipping sub-base preparation on Beaumont Clay. Before any pour, the clay subgrade must be moisture-conditioned (not too wet, not too dry), compacted to at least 95% Standard Proctor density, and topped with a minimum 4-inch compacted crushed stone base. For slab foundations, a vapor barrier (10-mil poly) is always required between the stone base and concrete. Skipping these steps can cause slab movement of 1–3 inches within the first few years — especially after heavy rainfall events or extended dry spells that cause the clay to shrink significantly.

      Beaumont Concrete Calculator — Common Project Types

      Beaumont’s construction landscape is shaped by its residential growth in the northwest corridors (Calder area, Parkdale, West End), active commercial and industrial expansion tied to the petrochemical refining industry, and ongoing flood recovery and infrastructure improvement projects throughout Jefferson County. Below are the most common concrete project types for Beaumont homeowners and contractors, along with standard local specifications.

      🚗 Beaumont Driveway Concrete

      A standard two-car Beaumont driveway (20×40 ft) at 4 inches requires approximately 10 cubic yards of 3,500 PSI concrete. Fiber mesh reinforcement (polypropylene, 1.5 lb/yd) is widely recommended over wire mesh in Beaumont because it distributes tension forces more effectively against clay-induced slab movement. Exposed aggregate and broom finishes are the most common — stamped concrete is popular in higher-end neighborhoods but adds $8–$15/sq ft to labor cost.

      • Minimum 4 inches thick — 5 inches strongly recommended on Beaumont clay
      • 3,500 PSI minimum — 4,000 PSI preferred for longevity in SE Texas heat
      • Fiber mesh or #3 rebar at 18 in. on center — both directions
      • Compacted crushed stone base — minimum 4 inches
      • Control joints every 10–12 ft to manage cracking
      • City of Beaumont building permit required for new driveways over 500 sq ft

      🏠 Beaumont Slab Foundation Concrete

      Post-tension monolithic slab foundations are the dominant foundation type in Beaumont residential construction — they are specifically engineered to flex with Beaumont Clay movement rather than crack under it. A typical 1,800 sq ft home foundation slab at 4 inches requires approximately 9 cubic yards. Post-tension cables are tensioned 28 days after pour. Always use a licensed PE-stamped foundation design in Jefferson County — this is required by the City of Beaumont for all new residential construction.

      ⚠️ Beaumont Foundation Warning — Never Skip the Engineer

      Jefferson County requires a licensed Texas PE-stamped foundation plan for all new residential concrete slab foundations. Beaumont’s highly expansive Vertisol clay soils (classified as “Very High” shrink-swell potential by USDA) can exert uplift pressures exceeding 2,000 lbs/sq ft during wet/dry cycles. A post-tension slab engineered specifically for your lot’s soil report is not optional — it is the difference between a 30-year slab and a 5-year cracking disaster. Contact City of Beaumont Building Permitting for requirements.

      🛤️ Beaumont Patio & Flatwork Concrete

      Backyard patios in Beaumont are one of the most popular concrete applications, driven by the region’s outdoor living culture. A standard 16×20 ft patio at 4 inches requires approximately 4 cubic yards. Decorative stamped concrete patios run $12–$22/sq ft installed in the Beaumont market. Always slope patios a minimum 1/8 inch per foot away from the home — Beaumont’s heavy rainfall (averaging 55 inches per year) makes proper drainage critical to prevent moisture intrusion under the foundation.

      Beaumont Concrete Bag Count Quick Reference

      Pre-mixed bags are best for small repairs, post holes, and projects under 1 cubic yard. For any project over 1 yard, ordering ready-mix from a Beaumont batching plant (such as Vulcan Materials, Martin Marietta, or local suppliers) is more cost-effective and delivers consistent quality. The table below shows standard bag counts for the most common Beaumont project sizes.

      Project Size Dimensions Cu Yards 60 lb Bags 80 lb Bags Recommendation
      Small Patio 10×10 ft × 4 in. 1.24 yd 56 bags 42 bags Bags OK
      Standard Patio 16×20 ft × 4 in. 3.95 yd 178 bags 133 bags Ready-Mix Better
      Single Driveway 10×20 ft × 4 in. 2.47 yd 111 bags 83 bags Ready-Mix Better
      2-Car Driveway 20×40 ft × 4 in. 9.88 yd 445 bags 334 bags Ready-Mix Required
      Home Foundation 40×45 ft × 4 in. 22.2 yd 999 bags 749 bags Ready-Mix Required
      Fence Post (each) 10 in. dia × 3 ft deep 0.06 yd 3 bags 2 bags Bags Ideal

      Small Patio — 10×10 ft × 4 in.

      Cubic Yards1.24 yd
      60 lb Bags56 bags
      80 lb Bags42 bags
      RecommendationBags OK

      2-Car Driveway — 20×40 ft × 4 in.

      Cubic Yards9.88 yd
      60 lb Bags445 bags
      80 lb Bags334 bags
      RecommendationReady-Mix Required

      Standard Patio — 16×20 ft × 4 in.

      Cubic Yards3.95 yd
      60 lb Bags178 bags
      80 lb Bags133 bags
      RecommendationReady-Mix Better

      Home Foundation — 40×45 ft × 4 in.

      Cubic Yards22.2 yd
      60 lb Bags999 bags
      80 lb Bags749 bags
      RecommendationReady-Mix Required

      Fence Post (each) — 10 in. dia × 3 ft

      Cubic Yards0.06 yd
      60 lb Bags3 bags
      80 lb Bags2 bags
      RecommendationBags Ideal

      Beaumont Concrete Calculator — 10 Pro Tips for SE Texas Pours

      Concrete work in Beaumont has unique requirements driven by the Beaumont Clay soil, subtropical climate, and high annual rainfall. These tips come directly from Southeast Texas contractor best practices and will help ensure your project lasts decades rather than years.

      • Always moisture-condition the clay subgrade — do not pour on bone-dry or saturated clay. Optimum moisture content for Beaumont Vertisol clay is approximately 20–25%.
      • Use a 4-inch minimum crushed stone base — TxDOT Grade 2 crushed limestone provides the drainage layer that Beaumont’s 55+ inches of annual rainfall demands.
      • Install a vapor barrier — 10-mil polyethylene under all slabs and foundations. Beaumont’s high groundwater table makes moisture vapor transmission a significant problem without it.
      • Schedule pours early in the morning — June through September, pour before 9 AM to avoid peak heat and humidity narrowing your finishing window.
      • Use a retarder admixture in summer — Ask your Beaumont ready-mix supplier for a Type B retarder mixed in at 3–5 oz/cwt to slow initial set and extend your finishing time.
      • Fiber mesh over wire mesh — Polypropylene fiber mesh (1.5 lb/yd) distributes tensile stress throughout the slab cross-section and is far more effective against clay movement than wire mesh.
      • Cut control joints within 12 hours — In Beaumont heat and humidity, saw-cut control joints as soon as the surface is firm enough to walk on. Space joints at 10–12 ft for 4-inch slabs.
      • Wet-cure for 7 days minimum — Apply curing compound immediately after finishing or use wet burlap and keep moist for 7 days minimum. Beaumont’s heat evaporates surface moisture faster than curing reactions can proceed.
      • Check flood zone before setting finish elevation — Many Beaumont properties are in FEMA AE or X500 flood zones. Your slab elevation must comply with local floodplain ordinance minimum finished floor elevation requirements.
      • Pull permits — always — The City of Beaumont actively enforces building permit requirements. Unpermitted concrete work can create title issues when selling your home.

      Beaumont Concrete Calculator — Frequently Asked Questions

      How much does a concrete driveway cost in Beaumont, TX?
      +
      A standard 20×40 ft two-car concrete driveway in Beaumont typically costs $4,500–$9,500 installed, depending on thickness, mix design, reinforcement type, and finish. Material (ready-mix at 3,500 PSI) runs approximately $1,500–$2,000 for ~10 cubic yards. Labor in the Beaumont market runs $3.50–$7.50/sq ft depending on crew experience and finish complexity. Stamped or colored decorative driveways run $12–$22/sq ft total installed. Always get 3 quotes from TDLR-licensed Beaumont concrete contractors.
      Why does Beaumont concrete crack so much?
      +
      The primary cause of premature cracking in Beaumont is the expansive Beaumont Clay (Vertisol) subgrade. This soil swells significantly when wet (gaining up to 30% volume) and shrinks dramatically when dry — creating powerful uplift and settlement forces beneath slabs. Secondary causes include inadequate base preparation, missing or improperly spaced control joints, over-watering the mix on hot days (which weakens the concrete), and finishing too early before bleed water rises. Using fiber mesh reinforcement, a proper compacted stone base, and correct joint spacing dramatically reduces cracking risk.
      Do I need a permit for a concrete driveway or patio in Beaumont?
      +
      Yes — the City of Beaumont requires a building permit for most concrete flatwork projects including driveways over 500 sq ft, new patio slabs, and all structural foundations. Permits are issued by the City of Beaumont Building Services Division (409-880-3100). Jefferson County also requires permits for construction in unincorporated areas. Skipping permits can result in stop-work orders, fines, and complications when selling your property. Your licensed contractor should pull the permit on your behalf as part of the project.
      What PSI concrete should I use in Beaumont, TX?
      +
      For most Beaumont residential projects, 3,500 PSI is the standard minimum. Use 4,000 PSI for driveways, exposed patios, and any slab subject to vehicle traffic. Post-tension slab foundations typically specify 3,500–4,000 PSI as required by the structural engineer’s stamped plan. For commercial and industrial applications in Beaumont’s petrochemical zone, 4,500–5,000 PSI is standard. Beaumont’s climate does not require air entrainment (no freeze-thaw cycles) — but a retarder admixture is recommended for all summer pours to manage the accelerated set caused by heat and humidity.
      How many cubic yards do I need for a Beaumont slab foundation?
      +
      Use the formula: (Length × Width × Thickness in inches ÷ 12) ÷ 27 × waste factor. A typical 1,500 sq ft Beaumont home footprint at 4 inches needs approximately 7.4 cubic yards + 10% waste = ~8.2 cubic yards ordered. A 2,000 sq ft footprint needs ~9.9 cubic yards + waste = ~11 cubic yards. Always confirm with your structural engineer’s foundation plan, as beam depths in post-tension designs add additional volume beyond the flat slab thickness. Our Beaumont Concrete Calculator above handles all these calculations instantly.
      What is the best time of year to pour concrete in Beaumont?
      +
      The ideal months for concrete pours in Beaumont are October through April, when temperatures are moderate (55–80°F) and humidity is lower. November through February offers the most predictable conditions. Summer pours (June–September) are possible but require careful planning: schedule delivery before 9 AM, use a retarder admixture, have your full crew on site before the truck arrives, and wet-cure immediately after finishing. Avoid pouring within 24 hours of heavy rain forecast — Beaumont’s clay soil rapidly becomes oversaturated and will not support compaction or pour equipment properly.

      Related Concrete Calculators


      🌴

      Florida Concrete Calculator

      Cubic yards, bags & FL ready-mix cost



      🏔️

      Colorado Concrete Calculator

      Cubic yards, bags & CO ready-mix cost



      🌵

      Arizona Concrete Calculator

      Cubic yards, bags & AZ ready-mix cost



      🏛️

      Connecticut Concrete Calculator

      Cubic yards, bags & CT ready-mix cost


      Beaumont Concrete Resources

      Official references and tools for Beaumont, TX concrete projects

      🏛️

      City of Beaumont Building Services

      Permits & Inspections

      Apply for building permits, check permit status, and verify contractor licenses for concrete projects in Beaumont. Required for driveways, foundations, and structural flatwork within city limits.

      Visit Beaumont Building Services
      📋

      Texas TDLR — Contractor Verification

      License Lookup

      Verify that your Beaumont concrete contractor holds a valid TDLR license before signing any contract. Texas law requires licensing for general contractors performing concrete and construction work.

      Search TDLR License Database
      🌊

      FEMA Flood Map — Beaumont TX

      Flood Zone Check

      Check your Beaumont property’s FEMA flood zone designation before setting finished slab elevation. Many areas of Jefferson County require minimum finished floor elevations above Base Flood Elevation (BFE).

      Check FEMA Flood Map