Concrete Leveling Grout Calculator (USA)
✅ 2026 Updated
Concrete Leveling Grout Calculator
USA Bags, Water Ratio, Void Fill & Cost Estimator
Calculate exact bags of concrete leveling grout, water-to-grout ratio, total volume for void fill or slab lifting, injection holes required, and full 2026 USA material and labor cost — for any mudjacking or cement grout leveling project.
50 lb
Standard Grout Bag (USA)
0.45–0.50
Typical Water-Grout Ratio
$18–$35
Per 50 lb Bag (2026 USA)
Free
No Sign-Up Required
🏗️ Slab Lifting
🕳️ Void Filling
🚗 Driveway Repair
🏠 Foundation Leveling
🛤️ Sidewalk Repair
Concrete leveling grout is a flowable, cement-based grout used for slab lifting (mudjacking), void filling beneath sunken slabs, column base plates, machine anchor bolts, and general sub-slab stabilization. Unlike self-leveling compound used for surface smoothing, leveling grout is pumped or pressure-injected under existing concrete to fill voids and restore slab elevation — making accurate volume estimation absolutely critical. Over-ordering wastes costly material; under-ordering leaves voids partially filled and the slab re-settling within months. This free Concrete Leveling Grout Calculator uses 2026 USA product data to calculate exact bag count, water volume, injection hole layout, working time, and total material cost for any slab lifting or void-fill project.
🧮 Free USA Tool
Leveling Grout Calculator
Bags · Water · Void Volume · Injection Holes · 2026 Cost
🏗️ Slab Lifting
🕳️ Void Fill
⚓ Base Plates
🏠 Residential & Commercial
Length of the sunken/uneven slab area
Width of the target slab area
Avg gap under slab or lift height needed
How much of the void volume needs grouting
Distance between drilled injection holes
Total Bags of Leveling Grout Needed
0 bags
Including waste/pump loss — 2026 USA rates
📦 Volume & Material
💰 Cost & Injection Layout
📊 Leveling Grout Application Guide — Void Fill vs. Lift Height
🟢 Minor Settlement (¼″–½″ lift)~30–50% void fill · Wide hole spacing
🔵 Typical Driveway / Sidewalk (½″–1″)~50–65% void fill · 3 ft grid
🔶 Significant Settlement (1″–2″)~75% void fill · 2–3 ft grid
🟣 Heavy Lift / Foundation (2″–4″)~85–100% void fill · 2 ft grid
🔴 Complete Void Fill (4″+)100% fill · Dense grid · Multi-stage pump
0.5
Water-Grout Ratio (typ.)
0.028
ft³ per lb of grout
+15%
Pump Loss (std.)
Minor ¼–½″
Typical ½–1″
Significant 1–2″
Heavy 2–4″
Full 4″+
What Is Concrete Leveling Grout?
Concrete leveling grout — also called non-shrink grout, flowable fill, or slab-lifting grout — is a cementitious, high-flow material used to fill voids beneath sunken concrete slabs and restore them to their original elevation. It differs fundamentally from self-leveling compound: SLC is applied to the top surface to smooth it, while leveling grout is pumped or pressure-injected through drilled holes into the void beneath the slab. According to the American Concrete Institute (ACI 351.1R), non-shrink grout is specified whenever zero volume change during curing is critical — such as under machinery base plates, bridge bearing pads, and column anchor bolts.
🔑 Grout vs. Self-Leveling Compound — Key Difference
Leveling grout fills the void beneath an existing slab to lift and support it — it is pumped through 1½″–2″ holes drilled into the slab, not poured on top. Self-leveling compound is applied to the top surface to smooth and flatten it before new flooring. Using SLC for slab lifting will fail immediately — it cannot carry structural load. Always use a compressive strength ≥ 5,000 psi non-shrink grout for any load-bearing slab lifting application.
How the Leveling Grout Calculator Works
The calculator converts your slab dimensions and average void depth to cubic feet, applies your void-fill percentage, adds pump waste loss, then divides by grout yield per 50 lb bag to compute bag count — plus water volume and injection hole grid layout.
📐 Core Leveling Grout Volume Formulas
Gross Void Volume (ft³) = Length × Width × (Void Depth ÷ 12)
Net Fill Volume (ft³) = Gross Void Volume × Void Fill %
Grout Volume with Waste (ft³) = Net Fill Volume × (1 + Waste Factor)
Bags Needed = Grout Volume (ft³) ÷ Yield per Bag (ft³/bag)
Water Volume (gal) = Bags × 50 lb × Water-Grout Ratio ÷ 8.34 lb/gal
Injection Holes = (Length ÷ Spacing + 1) × (Width ÷ Spacing + 1)
Leveling Grout Products — USA 2026 Comparison
Selecting the right grout type depends on compressive strength requirements, working time, flow characteristics, and application method. These are the most widely used USA leveling grout products in 2026:
| Grout Type | Yield / 50 lb Bag | Min Comp. Strength | Working Time | Price / Bag (2026) | Best For |
|---|---|---|---|---|---|
| Standard Non-Shrink | ~0.45 ft³ | 5,000 psi @ 28d | 20–30 min | ~$18/bag | General slab lifting, sidewalks, driveways |
| Flowable Fill (CLSM) | ~0.50 ft³ | 50–300 psi | 45–60 min | ~$20/bag | Utility trench backfill, non-structural voids |
| Rapid-Set Non-Shrink | ~0.42 ft³ | 6,000 psi @ 3 hrs | 10–15 min | ~$32/bag | Fast-track repairs, traffic restoration |
| High-Strength Precision | ~0.44 ft³ | 8,000 psi @ 28d | 20–25 min | ~$35/bag | Machine base plates, anchor bolts, bridges |
| Polymer-Modified | ~0.43 ft³ | 6,500 psi @ 28d | 25–35 min | ~$30/bag | Wet/below-grade conditions, high adhesion |
🟢 Standard Non-Shrink Grout
Yield / 50 lb Bag~0.45 ft³Comp. Strength5,000 psi @ 28dWorking Time20–30 minPrice (2026)~$18/bag
🔵 Flowable Fill / CLSM
Yield / 50 lb Bag~0.50 ft³Comp. Strength50–300 psiWorking Time45–60 minPrice (2026)~$20/bag
⚡ Rapid-Set Non-Shrink
Yield / 50 lb Bag~0.42 ft³Comp. Strength6,000 psi @ 3 hrsWorking Time10–15 minPrice (2026)~$32/bag
💪 High-Strength Precision
Yield / 50 lb Bag~0.44 ft³Comp. Strength8,000 psi @ 28dWorking Time20–25 minPrice (2026)~$35/bag
🔩 Polymer-Modified Grout
Yield / 50 lb Bag~0.43 ft³Comp. Strength6,500 psi @ 28dWorking Time25–35 minPrice (2026)~$30/bag
Application Method Guide — USA 2026
The method of grout placement significantly affects working time requirements, water-to-grout ratio, and bag yield. Each method has specific preparation steps and grout consistency requirements:
| Application Method | W/G Ratio | Consistency | Hole Size | Working Time Needed | Typical Use |
|---|---|---|---|---|---|
| Pump Injection | 0.45–0.50 | Fluid / Pumpable | 1.5″–2″ dia. | 20+ min | Mudjacking, slab lifting, sidewalks |
| Direct Pour | 0.40–0.45 | Flowable | Open trench | 30+ min | Open voids, trench backfill |
| Pressure Grouting | 0.38–0.42 | Stiff / Thick | 1″–1.5″ dia. | 15–20 min | Foundation cracks, anchor bolts |
| Gravity Fill | 0.42–0.48 | Self-leveling | N/A (formed) | 30+ min | Base plates, column setting |
💉 Pump Injection
W/G Ratio0.45–0.50Hole Size1.5″–2″ dia.Typical UseMudjacking / Slab Lift
🪣 Direct Pour
W/G Ratio0.40–0.45AccessOpen TrenchTypical UseOpen Void / Trench Backfill
🔩 Pressure Grouting
W/G Ratio0.38–0.42Hole Size1″–1.5″ dia.Typical UseFoundation / Anchor Bolts
⬇️ Gravity Fill
W/G Ratio0.42–0.48AccessFormed OpeningTypical UseBase Plates / Column Setting
💧 Water-to-Grout Ratio Is Critical
Adding too much water weakens the grout and causes segregation and shrinkage — the two leading causes of re-settlement after mudjacking. Never exceed the manufacturer’s maximum water-to-grout ratio (typically 0.50). Use the minimum water needed to achieve the required flowability for your application method, and always use a calibrated water meter rather than estimating by eye.
🕳️ Injection Hole Layout Rules
Holes are typically drilled in a 2–4 ft grid pattern across the slab surface using a rotary hammer drill with a 1½″–2″ core bit. Start pumping from the lowest point and work upward. Monitor adjacent holes for grout return — when fresh grout appears at a neighboring hole, that zone is filled. Patch all holes with hydraulic cement or rapid-set mortar immediately after grouting.
⏱️ Working Time Management
Non-shrink grout has a working time of 15–30 minutes — significantly shorter than standard concrete. For pump injection on large slabs, pre-batch all bags and keep the pump moving continuously to prevent line blockage. Rapid-set grouts (10–15 min working time) require a dedicated mixer operator and should not be used for large area lifts without a continuous flow system.
⚠️ Never Use Leveling Grout on Saturated Subgrade
If the void beneath the slab contains standing water or the subgrade is saturated, pumping grout will simply displace the water temporarily — the grout will not bond or cure properly and the slab will re-settle within weeks. The root cause of settlement (typically poor drainage or plumbing leaks) must be corrected before leveling grout is applied. Per ACI 351.1R, the substrate must be damp but free of standing water, and soil moisture content should be below 80% saturation before grouting begins.
✅ Cost Comparison — Leveling Grout vs. Full Slab Replacement
For residential driveways and sidewalks, concrete leveling grout (mudjacking) costs $3–$8 per sq ft in 2026, compared to full slab replacement at $8–$18 per sq ft. For a typical 200 sq ft driveway panel, leveling grout saves $1,000–$2,000 vs. full replacement — provided the existing slab is structurally sound (no major cracking or spalling). Always inspect the slab surface before committing to lifting — heavily cracked slabs are better replaced than lifted.
Concrete Leveling Grout — FAQ
How many bags of leveling grout do I need per cubic foot of void?+
Bags required per cubic foot of void (at 100% fill, before waste):
- Standard Non-Shrink (0.45 ft³/bag): ~2.2 bags/ft³
- Flowable Fill / CLSM (0.50 ft³/bag): ~2.0 bags/ft³
- Rapid-Set (0.42 ft³/bag): ~2.4 bags/ft³
- High-Strength Precision (0.44 ft³/bag): ~2.3 bags/ft³
- Polymer-Modified (0.43 ft³/bag): ~2.3 bags/ft³
Always add 15–20% for pump line loss and always round up to whole bags.
What is the correct water-to-grout ratio for slab lifting?+
For pump injection / mudjacking, the typical water-to-grout ratio is 0.45–0.50 by weight — meaning 0.45–0.50 lbs of water per 1 lb of dry grout. For a 50 lb bag:
- Minimum water (0.40 ratio): 20 lbs = ~2.4 gallons
- Standard water (0.45 ratio): 22.5 lbs = ~2.7 gallons
- Maximum water (0.50 ratio): 25 lbs = ~3.0 gallons
Never exceed the maximum ratio — excess water reduces compressive strength by up to 40% and causes long-term re-settlement.
How much does concrete mudjacking / slab lifting cost in the USA in 2026?+
2026 USA mudjacking cost ranges:
- Materials only (DIY): $1.50–$3.00/sq ft
- Professional mudjacking (cement grout): $3–$8/sq ft
- Polyurethane foam lifting (PolyLev): $5–$25/sq ft
- Full slab replacement (comparison): $8–$18/sq ft
A 10×20 ft driveway panel typically costs $600–$1,600 for professional mudjacking vs. $1,600–$3,600 for replacement. Material-only DIY pump rental adds $150–$350/day.
What size holes are drilled for leveling grout injection?+
Standard injection hole specifications:
- Diameter: 1½″–2″ for pump injection; 1″–1½″ for pressure grouting
- Spacing: 2–4 ft grid depending on void size and slab thickness
- Drill bit: Rotary hammer with SDS-plus core bit or spade bit
- Depth: Through the full slab thickness only — do not drill into the subgrade
- Patching: Fill with hydraulic cement or rapid-set mortar after grouting
Mark hole locations with chalk before drilling to ensure even grid coverage.
What is non-shrink grout and why is it used for leveling?+
Non-shrink grout is a cementitious material that experiences zero or positive volume change during curing — unlike standard concrete which shrinks 0.04–0.08% as it hydrates. This is critical for slab lifting because:
- Standard concrete shrinkage would leave micro-gaps under the lifted slab
- Non-shrink grout maintains full contact with the subgrade and slab underside
- It provides 5,000–8,000 psi compressive strength to permanently support load
- ASTM C1107 governs non-shrink grout performance standards in the USA
Related Concrete Calculators
Portland Concrete Calculator
Volume & cost for Portland, OR
Providence Concrete Calculator
Estimates for Providence, RI
Provo Concrete Calculator
Concrete estimates for Provo, UT
Providence Slab Calculator
Slab estimator for Providence, RI
Trusted USA Leveling Grout Resources
Industry standards and manufacturer references for non-shrink grout specification and application.
📐
ACI 351.1R — Grouting Guide
Industry Standard
ACI 351.1R is the American Concrete Institute’s authoritative guide on grouting for support of equipment and machinery — covering non-shrink grout selection, mixing, placement, and curing requirements for all USA structural grouting applications including slab lifting and base plate setting.
ASTM C1107 — Non-Shrink Grout
Federal Standard
ASTM C1107 is the standard specification for packaged dry hydraulic-cement grout (non-shrink) used in all USA structural leveling applications. It defines performance requirements for pre-hardening and post-hardening height change, compressive strength, and flowability — essential for specifying grout for structural slab lifting projects.
FHWA — Flowable Fill Guide
Federal Resource
The Federal Highway Administration’s Controlled Low-Strength Material (CLSM) guide provides state DOT specifications and design guidance for flowable fill in highway and municipal applications — including void filling beneath bridge approaches, utility trenches, and road slab undersealing across all US states.