Concrete Line Pump Calculator (USA)
✅ 2026 REED / ACI Updated
Concrete Line Pump Calculator
USA Output, Pipeline Pressure & Distance Estimator
Calculate required concrete line pump output (yd³/hr), total pipeline pressure (psi), maximum horizontal and vertical pumping distance, pour duration, and pump size recommendation — using 2026 USA industry data from REED Concrete Pumps and ACI 304R pumping guidelines.
20–70
yd³/hr Line Pump Output Range (USA)
2,200ft
Max Horizontal Distance (REED B50)
875ft
Max Vertical Distance (REED B50)
Free
No Sign-Up Required
🏠 Residential Slabs
🏗️ Commercial Foundations
🏔️ High-Rise Pumping
📏 Pipeline Pressure
⏱️ Pour Duration
A concrete line pump (also called a trailer-mounted pump or ground line pump) uses a hydraulic piston system to push concrete through a connected pipeline of steel pipes and flexible hoses — delivering concrete precisely to any location on a job site. Unlike boom pumps (which have a self-contained articulating arm), line pumps require the crew to manually lay out and connect a pipeline from the pump to the pour location. They are the preferred choice for residential slabs, foundations, swimming pools, driveways, and any pour within 500 linear feet. Per 2026 REED Concrete Pumps specifications, USA line pumps deliver 20–70 yd³/hr at concrete pressures of 1,000–2,113 psi, with maximum theoretical horizontal distances of 750–2,200 ft and vertical distances of 300–875 ft. This free calculator estimates the required output, pipeline pressure, pour time, and appropriate pump model size for your project.
🔴 Free USA Pumping Tool
Line Pump Calculator
Output · Pipeline Pressure · Distance · Pour Duration · Pump Size — 2026 USA
📊 yd³/hr Output
💨 PSI Pressure
📏 Distance Check
⏱️ Pour Time
🏗️ Project Volume & Pour Requirements
Total volume for the pour — not including waste allowance
Time available for the pour incl. setup & cleanup buffer
📏 Pipeline Configuration
Total horizontal length of steel pipe + hose runs
Total rise from pump to pour point (0 for ground-level)
Each 90° elbow ≈ 15 ft equivalent straight pipe (pressure)
Each 45° elbow ≈ 8 ft equivalent straight pipe
Flexible rubber end hoses — add ~10 ft equiv. each
⚙️ Mix Design & Pump Parameters
Required Pump Output Rate
0 yd³/hr
2026 USA · REED Pump Reference · ACI 304R Methodology
📊 Output & Volume
💨 Pipeline Pressure
🚛 Logistics & Trucks
📊 Pressure Contribution by Pipeline Component
🔴 Concrete Line Pump System — USA 2026 Key Parameters
🔴 Pump Unit (Trailer-Mounted)Output: 20–70 yd³/hr · Pressure: 1,000–2,113 psi
📏 Steel Pipe Run3″–5″ dia · 10 ft sections · ~5 psi/ft resistance
↗️ Vertical Rise Section1 vertical ft = 10–12 horizontal ft equivalent pressure
🔄 Elbows & Fittings90° elbow ≈ 15 ft · 45° elbow ≈ 8 ft equivalent
🟢 Flexible End Hose5 ft rubber hose = ~10 ft steel pipe equivalent
⚡ Start-Up Pressure20–29 psi base · Safety factor 10–25% added
20–70
yd³/hr Output (REED B20–B70)
4″
Standard USA Line Pump Pipe Dia.
80%
Typical Field Pump Efficiency
Pump Unit
Steel Pipe
Vertical Rise
Elbows
End Hose
What Is a Concrete Line Pump?
A concrete line pump is a trailer-mounted hydraulic piston pump that forces concrete through a connected network of rigid steel pipes and flexible rubber hoses directly to the placement location. The pump uses a two-cylinder reciprocating action — while one cylinder pushes concrete into the pipeline, the other refills from the hopper — creating a near-continuous flow. Unlike boom pumps (which have a mounted articulating arm on a truck chassis), line pumps require the crew to manually set up and move the pipeline as pouring progresses. They are the standard choice for residential and light commercial concrete work across the USA, handling slabs, foundations, pools, walls, and any application where a boom pump is not economically justified or where site access restricts large truck entry.
🔴 Line Pump vs. Boom Pump — When to Use Each
Use a line pump when: project volume is under 100 yd³, pipeline distance is under 500 ft, site access prevents large trucks, pour is at or near ground level, project budget is limited ($800–$1,500/day vs. $1,500–$3,500/day for boom pumps), or pour locations require repositioning of the delivery point. Use a boom pump when: project volume exceeds 75–100 yd³ in a single pour, concrete must be delivered above 3–4 stories, site conditions make pipeline laying impractical, or pour speed is critical (boom pumps deliver 60–180 yd³/hr vs. 20–70 yd³/hr for line pumps). Both use the same concrete mix requirements per ACI 304R.
How the Calculator Works — Line Pump Sizing Method
The calculator follows the industry-standard pressure loss method used by REED Concrete Pumps and the ACI 304R Guide for Measuring, Mixing, Transporting, and Placing Concrete. It computes required output rate, then calculates total system pressure from each pipeline component, and cross-references against standard REED pump model specifications to recommend the appropriate pump class.
🔴 Concrete Line Pump Calculation Formulas
Required Output (yd³/hr) = [Volume × (1 + safety%)] / [Pour Hours × Efficiency]
Pipe Friction Loss (psi) = Equiv. Length (ft) × friction_factor (psi/ft)
Equiv. Length = Horiz. ft + (Vert. ft × 10) + (90° elbows × 15) + (45° elbows × 8) + (end hoses × 10)
Friction Factor: 3″ pipe ≈ 8 psi/ft · 4″ pipe ≈ 4.5 psi/ft · 5″ pipe ≈ 2.5 psi/ft (at std slump)
Slump Correction: 3″ slump ×1.35 · 4″ ×1.00 · 5″ ×0.82 · 6″+ ×0.65
Total Pressure (psi) = Start-Up (25 psi) + Pipe Friction + Vertical Head + Safety Margin
Power Required (hp) = (Pressure [psi] × Output [yd³/hr] × 27) / (396,000 × η)
Trucks/hr Required = Required Output (yd³/hr) / Truck Capacity (yd³)
REED Line Pump Specifications — USA 2026
These are the official REED Concrete Pumps B-Series specifications — the most widely used line pump series in the USA. Use the table to cross-check the calculator’s pump recommendation against actual machine capabilities:
| Model | Max Output (yd³/hr) | Max Pressure (psi) | Max Horiz. Distance | Max Vert. Distance | Engine |
|---|---|---|---|---|---|
| REED B20 | 20 yd³/hr | 1,664 psi | 1,650 ft | 700 ft | 110 hp Cummins 4.5L |
| REED B50 | 50 yd³/hr | 2,113 psi | 2,200 ft | 875 ft | 110 hp Cummins 4.5L |
| REED B60 | 60 yd³/hr | 1,174 psi | 950 ft | 375 ft | 130 hp Cummins 4.5L |
| REED B70 | 70 yd³/hr | 1,305 psi | 1,150 ft | 390 ft | 130 hp Cummins 4.5L |
| General Small Line Pump | 15–25 yd³/hr | 1,200–1,800 psi | 800–1,200 ft | 300–500 ft | 80–110 hp diesel |
| General Mid Line Pump | 30–50 yd³/hr | 1,500–2,100 psi | 1,200–2,000 ft | 500–800 ft | 110–130 hp diesel |
| General Large Line Pump | 55–70 yd³/hr | 1,000–1,400 psi | 750–1,200 ft | 300–450 ft | 130 hp diesel |
🔴 REED B20 — Small Line Pump
Max Output20 yd³/hr
Max Pressure1,664 psi
Max Horizontal1,650 ft
Max Vertical700 ft
🔴 REED B50 — Mid Line Pump (Most Common)
Max Output50 yd³/hr
Max Pressure2,113 psi
Max Horizontal2,200 ft
Max Vertical875 ft
🔴 REED B70 — Large Line Pump
Max Output70 yd³/hr
Max Pressure1,305 psi
Max Horizontal1,150 ft
Max Vertical390 ft
Pipeline Pressure Loss Reference — USA 2026
These friction loss values per linear foot are based on ACI 304R and REED pump technical data for standard 4″ pumpable concrete mixes. Actual losses vary with mix design, pump output rate, and aggregate type:
| Component | 3″ Pipe (psi) | 4″ Pipe (psi) | 5″ Pipe (psi) | Notes |
|---|---|---|---|---|
| Straight Steel Pipe (per ft) | 7–9 psi/ft | 4–5 psi/ft | 2–3 psi/ft | At 4″ slump, standard mix |
| 90° Elbow (equiv. ft) | ≈ 15 ft pipe | ≈ 15 ft pipe | ≈ 15 ft pipe | Adds ~60–135 psi per elbow (4″ pipe) |
| 45° Elbow (equiv. ft) | ≈ 8 ft pipe | ≈ 8 ft pipe | ≈ 8 ft pipe | Adds ~32–72 psi per elbow (4″ pipe) |
| Flexible Rubber End Hose (5 ft) | ≈ 15 ft pipe | ≈ 10 ft pipe | ≈ 10 ft pipe | Higher friction than steel pipe |
| Vertical Rise (per ft) | +0.434 psi/ft | +0.434 psi/ft | +0.434 psi/ft | Hydrostatic head only (gravity) |
| Start-Up Pressure | 25–30 psi | 25–30 psi | 20–25 psi | Fixed system start pressure |
| Slump Multiplier (3″ slump) | ×1.35 | ×1.35 | ×1.35 | Stiff mix = much higher friction |
| Slump Multiplier (5″ slump) | ×0.82 | ×0.82 | ×0.82 | Fluid mix = significantly lower friction |
📏 Straight Pipe Friction Loss
3″ diameter7–9 psi/ft
4″ diameter (standard)4–5 psi/ft
5″ diameter2–3 psi/ft
🔄 Fittings Equivalent Length
90° Elbow≈ 15 ft pipe
45° Elbow≈ 8 ft pipe
5 ft Flex Hose≈ 10 ft pipe
🔑 The Slump-Pressure Relationship
Slump is the single most impactful variable in concrete pumpability. At 3″ slump, pipeline friction is 35% higher than at the 4″ reference point — dramatically increasing required pump pressure. At 5″ slump, friction drops to 82% of reference. For long or complex pipeline layouts, specifying a 4.5–5″ slump with a mid-range water reducer is the most effective way to reduce pump pressure without increasing water content. Per ACI 304R, the practical minimum slump for reliable pumping through a 4″ steel pipe is 4 inches — attempting to pump stiffer mixes risks pipeline blockage (plugging) and pump damage.
🚛 Truck Synchronization Is Critical
A concrete line pump running at 30 yd³/hr requires a new 8 yd³ truck every 16 minutes. If trucks arrive late, the pump must slow or stop — which can cause the concrete in the pipeline to begin to set, leading to a blockage. ACI 304R recommends maintaining a continuous flow rate and coordinating truck delivery intervals to match pump output. The calculator computes required trucks/hour and minimum inter-truck interval — always share this figure with your ready-mix plant dispatcher when scheduling the pour so they can stage trucks appropriately.
📏 Aggregate Size Rules for Line Pumps
ACI 304R establishes the 1/3 rule for concrete pumpability: maximum aggregate size must not exceed 1/3 of the pipe inside diameter. For a standard 4″ (102mm) line pump, this limits maximum aggregate to 1⅓” — so 1″ aggregate is the practical maximum for 4″ pipe. REED Concrete Pumps specifies a maximum of 1½” aggregate for their 5″–7″ cylinder B50/B60/B70 models and ¾” for the smaller B20 (4″ cylinder, 4″ outlet). Using oversized aggregate is the most common cause of line pump blockages in the USA — always verify aggregate size against the pump outlet diameter before the pour begins.
⚠️ Pipeline Blockage — Prevention & Recovery
A concrete blockage (plug) in the pipeline is the most costly line pump failure — requiring pipeline disassembly, cleaning, and potentially losing the pour window. Prevention checklist: (1) Prime the pipeline with 2–3 gallons of neat cement slurry before the first concrete; (2) Never stop pumping for more than 15–20 minutes without slowly reversing the pump to relieve pressure; (3) Use the correct slump (4″+ minimum) and verify aggregate size; (4) If a blockage occurs, reverse the pump first — do NOT continue forward pressure; (5) Inspect all fittings before the pour for concrete buildup from previous uses. Most blockages occur at elbows and reducers — these are the first points to inspect and disassemble when clearing a plug.
✅ Line Pump Rental Cost Guide — USA 2026
- Small line pump (20–25 yd³/hr): $700–$1,000/day including operator
- Mid line pump (30–50 yd³/hr): $900–$1,500/day including operator
- Large line pump (55–70 yd³/hr): $1,200–$2,000/day including operator
- Pipeline setup / teardown: Included in most rental rates; $150–$300 extra for long pipeline runs (>300 ft)
- Cleaning charge: $75–$150 per use for pipeline washout
- Mobilization fee: $150–$400 depending on distance from pump yard to job site
Concrete Line Pump — Frequently Asked Questions
What is the maximum distance a concrete line pump can pump?+
Per REED Concrete Pumps 2026 specifications:
- Horizontal distance (theoretical max):
B20: 1,650 ft · B50: 2,200 ft · B60: 950 ft · B70: 1,150 ft - Vertical distance (theoretical max):
B20: 700 ft · B50: 875 ft · B60: 375 ft · B70: 390 ft - Practical real-world distances are typically 50–70% of theoretical maximums due to mix design variation, equipment wear, and elbow losses
- Rule of thumb: 1 vertical foot of pipe = 10–12 horizontal feet in pressure terms — a 100 ft vertical rise adds the pressure equivalent of 1,000–1,200 ft of horizontal pipe
Always add a 15–20% safety margin to your calculated pressure and verify against your specific pump model’s rated pressure.
What slump do I need for concrete pumping?+
ACI 304R minimum slump recommendations for pumped concrete:
- 4″ minimum slump for standard 4″ pipeline line pump — below this, risk of blockage increases significantly
- 5″–6″ slump is preferred for long pipeline runs (>200 ft) or complex layouts with multiple elbows
- 3″ slump mixes can be pumped only at very high pressure in short, simple pipelines — not recommended for line pumps without a water reducer admixture
- SCC (Self-Consolidating Concrete, 7″+ slump) pumps very easily — however, the mix must be designed for pumpability to prevent segregation under pump pressure
When ordering ready-mix for a pumped pour, specify “pump mix” to the batch plant — they will design the mix with appropriate admixtures for pumpability at your required strength.
How many yd³/hr does a line pump produce?+
2026 USA line pump output by class:
- Small residential line pump: 15–25 yd³/hr (sufficient for driveways, residential slabs under 50 yd³)
- Standard mid line pump (most common rental): 30–50 yd³/hr — covers most commercial foundations and parking lots
- Large line pump: 55–70 yd³/hr — large floor pours, tilt-up panels, warehouse slabs
- Actual output in field is typically 75–85% of rated maximum due to truck wait times, pump cycling, and pipeline friction at higher distances
For residential work, a 30 yd³/hr pump handles most pours comfortably. Factor in a 15–20% contingency when calculating required output rate.
What size aggregate can a line pump handle?+
ACI 304R maximum aggregate size (1/3 rule):
- 3″ pipe: Maximum ⅜” aggregate (mortar pump)
- 4″ pipe (standard USA line pump): Maximum 1″ aggregate (practical); 1½” possible in some mixes
- 5″ pipe (large line pump): Maximum 1½” aggregate
- REED specification: B20 (4″ outlet) = ¾” max; B50/B60/B70 (5″ outlet) = 1½” max
Using oversized aggregate is the #1 cause of line pump blockages. When in doubt, use ¾” aggregate — it pumps reliably through all standard line pump sizes, meets virtually all residential and commercial mix design requirements, and allows lower pipeline pressures.
How do I calculate how many trucks per hour I need for a line pump?+
Truck synchronization formula for line pump pours:
- Trucks/hour = Required Output (yd³/hr) ÷ Truck Load (yd³)
- Example: 30 yd³/hr pump ÷ 8 yd³ truck = 3.75 trucks/hr = one truck every 16 minutes
- Minimum inter-truck interval: Contact your ready-mix plant with this interval so they can stage trucks — not just order by volume
- Add 1 buffer truck: Always have one extra truck on standby at the plant to cover any delivery delay — a 20-minute gap can cause concrete in the pipeline to begin setting in warm weather
- Hot weather (85°F+): Reduce inter-truck interval by 25% and order ice or chilled water in the mix if pour duration exceeds 90 minutes
Related Concrete Calculators
Portland Concrete Calculator
Volume & cost for Portland, OR
Providence Concrete Calculator
Estimates for Providence, RI
Provo Concrete Calculator
Concrete estimates for Provo, UT
Providence Slab Calculator
Slab estimator for Providence, RI
Trusted USA Concrete Pumping Resources
Manufacturer specifications, ACI guidelines, and pumping calculators for USA concrete line pump projects.
🔴
REED Concrete Pumps B-Series
Manufacturer Data
REED’s B-Series line pump specifications provide the authoritative 2026 USA benchmark data for output (yd³/hr), maximum pressure (psi), horizontal and vertical pumping distances, cylinder sizes, and engine ratings — the reference standard used by contractors, rental companies, and engineers across all 50 US states for line pump selection.
Long-Distance Pumping Calculator
Online Tool
BestSupportUnderground’s long-distance concrete pumping calculator provides a detailed pressure loss calculation tool covering pipeline length, vertical height, elbow count, end hoses, and safety factors — useful for verifying complex pipeline layouts before committing to a pump model for long-distance or high-rise USA concrete placements.
ACI 304R — Placing Concrete
ACI Standard
ACI 304R (Guide for Measuring, Mixing, Transporting, and Placing Concrete) is the primary USA standard governing concrete pumping requirements — including mix design for pumpability, minimum slump requirements, aggregate size limits, pipeline sizing, pressure calculations, and blockage prevention procedures for all line pump and boom pump applications.